************************************** DRIFT KINETIC CODE PARAMETERS ******************************************** ****************************************************************************************************************** Create the local file DKEPARAM_dkeparam_id.mat by Y.Peysson CEA-DRFC <yves.peysson@cea.fr> and Joan Decker MIT-RLE (jodecker@mit.edu)
0001 %************************************** DRIFT KINETIC CODE PARAMETERS ******************************************** 0002 %****************************************************************************************************************** 0003 % Create the local file DKEPARAM_dkeparam_id.mat 0004 % 0005 %by Y.Peysson CEA-DRFC <yves.peysson@cea.fr> and Joan Decker MIT-RLE (jodecker@mit.edu) 0006 % 0007 clear all 0008 dkeparam_id = 'UNIFORM10010020_coll0';%Set here the name (identifier) of the drift kinetic code parameters 0009 % 0010 %Mesh size calculation 0011 % 0012 dkeparam.grid_uniformity = 1;%Pitch-angle and momentum grids uniformity: (0) no, (1) yes (-1 for specific test for DKE, transient and pitch-angle grid only) 0013 dkeparam.grid_method = 1;%Pitch-angle grid calculation technique: (0): old method, (1) new method 0014 dkeparam.nmhu_S = 101;%Number of angular values for the flux grid (WARNING: odd number) (>100 recommended for accurate run) 0015 dkeparam.np_S = 101;%Number of momentum values for the flux grid (pnmax/np < 0.1 highly recommended for accurate run) WARNING: must be adjusted so that effective momentum point number is larger than thepitch-angle one. 0016 dkeparam.pnmax_S = 20;%Maximum value of the flux momentum grid (pth_ref) 0017 % 0018 %Pitch-angle grid 0019 % 0020 dkeparam.sfac0 = 1; % reduction factor for fine grid near mhu = 0 0021 dkeparam.sfac1 = 1; % reduction factor for fine grid near abs(mhu) = 1 0022 dkeparam.sfact = 1; % reduction factor for fine grid near abs(mhu) = mhut 0023 % 0024 dkeparam.snmhu0 = 1; % number of fine grid points near mhu = 0 0025 dkeparam.snmhu1 = 1; % number of fine grid points near abs(mhu) = 1 0026 dkeparam.snmhut = 1; % number of fine grid points near abs(mhu) = mhut 0027 % 0028 dkeparam.grid_power = 1.5; % power for mhu grid step varations (grid_power > 1) (Note: for grid_method = 1 only) 0029 % 0030 %Momentum grid 0031 % 0032 dkeparam.np_S_ref = 20;%position in the mpomentum grid where dpn_S is twice the minimum value(must be ajusted with snp parameter) 0033 dkeparam.snp = 1;%pgridfactor (Uniform grid: pgridfactor = 1, non-uniform grid: pgridfactor > 1) 0034 dkeparam.spfac = 20;%reduction factor for the momentum supergrid used in collision integrals 0035 % 0036 %Normalized radii at which the distribution is calculated (DKE or FP) 0037 %The syntax rho='all' may be also used if all mhu values are considered. 0038 % 0039 dkeparam.dpsin_dke = 0.01;%maximum difference between two consecutive positions used for radial derivatives 0040 % 0041 dkeparam.ref_mode = 0;%Reference values: (0) from core Te and ne, (1) from Te and ne at the normalized radius (paramater only active for a single radial value, otherwise ref_mode = 0) 0042 % 0043 % Dql and collision operator 0044 % 0045 dkeparam.coll_mode = 0;%No collision operator (space plasmas): (-1), Relativistic collision operator: (0), Relativistic Maxwellian background, (1) High-velocity limit, (2) Linearized Belaiev-Budker (3) Non-relativistic Lorentz model, (4) Non-relativistic Maxwellian background 0046 % 0047 % Ray-tracing and RF waves 0048 % 0049 dkeparam.rt_mode = 0;%RT-DKE power consistency 0050 dkeparam.abs_lim = 0.95;%Relative level of RF power absorption that is accpeted for in the quasilinear convergence loop (0: no threshold, 1: full absorption) 0051 dkeparam.nit_rf = 20;%Maximum number of iteration in ray-tracing. Works only if rt_mode = 1 and more than one radial point (default = 1) 0052 dkeparam.prec_rf = 1e-4;%relative precision in RT-DKE iterations 0053 dkeparam.n_rf_list = 0;%List of harmonics in the Dql calculations 0054 dkeparam.delta_rt = 0;%smoothering parameter of quasilinear iterations 0055 dkeparam.nk_abs = 1;%maximum number of iterations on a_sdNpar for full absorption (%%%%%%TODO%%%%%%% for what ?) 0056 %dkeparam.w_mask = ;%%%%%%TODO%%%%%%% 0057 %dkeparam.rho0 = ;%%%%%%TODO%%%%%%% 0058 %dkeparam.seekparam.submode = ;%%%%%%TODO%%%%%%% 0059 %dkeparam.seekparam.f_sdNpar_in = ;%%%%%%TODO%%%%%%% 0060 %dkeparam.seekparam.f_step = ;%%%%%%TODO%%%%%%% 0061 %dkeparam.seekparam.a_sdNpar_in = ;%%%%%%TODO%%%%%%% 0062 %dkeparam.seekparam.a_step = ;%%%%%%TODO%%%%%%% 0063 % 0064 % Run mode 0065 % 0066 dkeparam.bounce_mode = 0;%Bounce averaging option: (0) no bounce averaging, (1) bounce averaging full implicit method with 15 diagonals 0067 dkeparam.dke_mode = 0;%Fokker-Planck equation (0), Drift Kinetic equation (1) 0068 dkeparam.equil_mode = 1;%Equilibrium option: (0) circular concentric flux-surfaces, (1) numerical equilibrium 0069 dkeparam.syn_mode = 0;%Synergy calculation: (0) none, (1) yes: the code runs twice, including once without RF or electric fields. (only if dke_mode = 1) 0070 % 0071 dkeparam.norm_mode_f = 0;%Local normalization of f0 at each iteration: (0) no, the default value when the numerical conservative scheme is correct, (1) yes 0072 dkeparam.boundary_mode_f = 1;%Number of points where the Maxwellian distribution is enforced from p = 0 (p=0, free conservative mode but param_inv(1) must be less than 1e-4, otherwise 1e-3 is OK most of the time. Sensitive to the number of points in p) 0073 dkeparam.prec0_f = 1e-11;%Convergence level of the residu. If NaN, dkeparam.nit_f calculations are performed, whatever the level of the residu. 0074 dkeparam.nit_f = 50;%Maximum number of iterations for f (> 1) 0075 dkeparam.initguess_f = 0;%Initial guess for the distribution function: (0) Maxwellian, (1) Fuchs model with Tperp for LH current drive only, (2) from a file 0076 dkeparam.initfile_f = '';%If initguess_f = 2. The file must be in the directory Project_DKE, and created by dke_4_1yp.m 0077 % 0078 dkeparam.boundary_mode_g = 0;%Number of points where the first distribution function for the Lorentz model is enforced from p = 0 (p=0, free conservative mode but param_inv(1) must be less than 1e-4, otherwise 1e-3 is OK most of the time. Sensitive to the number of points in p) 0079 dkeparam.prec0_g = 1e-11;%Convergence level of the residu (if NaN, iterations stop with nit_g) 0080 dkeparam.nit_g = 50;%Maximum number of iterations for g 0081 % 0082 dkeparam.tn = 100000;%LUKE time step (1/nhuth_ref) 0083 dkeparam.dtn = NaN;%Integration time step (1/nhuth_ref) (dtn > 0: fully implicit time differencing scheme , dtn < 0: Crank-Nicholson time differencing scheme) (WARNING: dtn less than 1 when fast electron radial transport is considered) 0084 dkeparam.opsplit = 0;%Operator splitting between momentum and radial dynamics (for tests only) (opsplit = 0: no operator splitting , opsplit = 1: operator splitting). If this field does not exist, it is equivalent to dkeparam.opsplit = 0. 0085 % 0086 dkeparam.invproc = 1;%Iterative matrix inversion methods 0087 % (3) Matlab built-in qmr iterative method (MatLab built-in partial LU factorization used) 0088 % (2) Matlab built-in bicg iterative method (MatLab built-in partial LU factorization used) 0089 % (1) Matlab built-in cgs iterative method (MatLab built-in partial LU factorizsation used) 0090 % (0) Matlab built-in direct inversion without any LU factorization (NOT RECOMMANDED !) 0091 % (-1): MUMPS parallel (or sequential) fortran 95 direct inversion (LU matrix factorization done for each time a matrix inversion is called) 0092 % (-2): MUMPSMEX sequential fortran 95 inversion using MUMPS LU matrix factorization 0093 % (-3): SUPERLUMEX sequential direct matrix inversion (LU matrix factorization done for each time a matrix inversion is called) 0094 % (-4) PETSc interface (see data structure below) 0095 dkeparam.ludroptol = 1e-5;%Drop tolerance for the built-in MatLab partial LU decomposition (recipes: droptol = max(1/dtn/nr,param_inv(1))) 0096 dkeparam.mlmaxitinv = 4;%Maximum number of iterations for iterative built-in MatLab matrix inversion method (between 1 and 20 usualy, if empty, mlmaxitinv = min(matrixdim,20). See matlab documentation. 0097 dkeparam.mlprecinv = 1e-5;%Accuracy for the MatLab build-in matrix inversion. 0098 dkeparam.MUMPSparam.nproc = 1;%number of processor used by MUMPS (depends of the computer framework). Default is 1 0099 dkeparam.MUMPSparam.thresholdpivoting = '';%Relative threshold for numerical pivoting in the MUMPS partial LU decomposition (default MUMPS = 1e-2: NaN or empty or field not existing). Increasing this parameter will reduce sparcity. Less than 1. 0100 dkeparam.MUMPSparam.precinv = '';%Accuracy for the MUMPS matrix inversion.(default MUMPS: NaN or empty or field not existing). Only for the solve phase. 0101 dkeparam.PETScparam.nproc = 1;%number of processor used by PETSc (depends of the computer framework). Default is 1 0102 dkeparam.PETScparam.matrixtype = ' ';%Matrix type used by PETSc. For SUPERLU use '-matload_type superlu_dist' otherwise ' '. See PETSc documentation 0103 dkeparam.PETScparam.kspmethod = ' ';%KSP method used by PETSc. '-ksp_type preonly': no iteration, direct matrix solve. Otherwise '-ksp_type bicg' or '-ksp_type bcgs' for example. See PETSc documentation 0104 dkeparam.PETScparam.pcmethod = ' ';%Preconditioning method used by PETSc. '-pc_type lu' for SUPERLU or '-pc-type hypre' for HYPRE. See PETSc documentation 0105 dkeparam.PETScparam.cloop = 0;%First order collision selfconsistency is done internaly in C (1) or in MatLab (0) 0106 % 0107 dkeparam.clustermode.coll_dke_jd.scheduler.mode = 0;%MatLab distributed computing environment disabled (0), enabled with the dedicated toolbox (1), enabled with a private method (2) for the function coll_dke_jd.m (MDC toolbox must be installed for option 1) 0108 dkeparam.clustermode.coll_dke_jd.scheduler.timeout = 200;%MatLab distributed computing environment time out (s). after time out is reached, calculations are performed in a sequential mode on a single processor 0109 dkeparam.clustermode.coll_dke_jd.scheduler.size = 2;%MatLab distributed computing environment cluster size. Can be Inf is all the processors of the cluster are free for distributed calculations 0110 dkeparam.clustermode.eecoll_dke_yp.scheduler.mode = 0;%MatLab distributed computing environment disabled (0), enabled with the dedicated toolbox (1), enabled with a private method (2) for the function coll_dke_jd.m (MDC toolbox must be installed for option 1) 0111 dkeparam.clustermode.eecoll_dke_yp.scheduler.timeout = 200;%MatLab distributed computing environment time out (s). after time out is reached, calculations are performed in a sequential mode on a single processor 0112 dkeparam.clustermode.eecoll_dke_yp.scheduler.size = 2;%MatLab distributed computing environment cluster size. Can be Inf is all the processors of the cluster are free for distributed calculations 0113 dkeparam.clustermode.wave_solver_yp.scheduler.mode = 0;%MatLab distributed computing environment disabled (0), enabled with the dedicated toolbox (1), enabled with a private method (2) for the function coll_dke_jd.m (MDC toolbox must be installed for option 1) 0114 dkeparam.clustermode.wave_solver_yp.scheduler.timeout = 200;%MatLab distributed computing environment time out (s). after time out is reached, calculations are performed in a sequential mode on a single processor 0115 dkeparam.clustermode.wave_solver_yp.scheduler.size = 2;%MatLab distributed computing environment cluster size. Can be Inf is all the processors of the cluster are free for distributed calculations 0116 dkeparam.clustermode.wave_random_yp.scheduler.mode = 0;%MatLab distributed computing environment disabled (0), enabled with the dedicated toolbox (1), enabled with a private method (2) for the function coll_dke_jd.m (MDC toolbox must be installed for option 1) 0117 dkeparam.clustermode.wave_random_yp.scheduler.timeout = 200;%MatLab distributed computing environment time out (s). after time out is reached, calculations are performed in a sequential mode on a single processor 0118 dkeparam.clustermode.wave_random_yp.scheduler.size = 2;%MatLab distributed computing environment cluster size. Can be Inf is all the processors of the cluster are free for distributed calculations 0119 % 0120 dkeparam.opt_struct = 0;% (0) select only main fields from output structures (1) select all fields except ZXYD_rf and gridindex_rf (2) also select ZXYD_rf and gridindex_rf 0121 dkeparam.store_mode = 0;%Temporary storing option for sparse matrices calculations (in RAM: 0, in disk file 1) when memory space is tight 0122 dkeparam.opt_save = 0;%Save intermediate calculations 0123 dkeparam.opt_load = 0;%Load intermediate calculations 0124 dkeparam.timevol = 0;% save results at intermediate times 0125 % 0126 dkeparam.method = 'spline';%For the pitch-angle interpolation in the prjectioon of the electron velocity distribution on the Legendre polynomial basis 0127 dkeparam.n_gauleg = 35;%Number of Legendre polynomials for projections of the electron velocity distribution 0128 dkeparam.epsi_gauleg = 1e-14;%Accuracy of the Legendre projection 0129 % 0130 eval(['save DKEPARAM_',dkeparam_id,'.mat dkeparam']);